IMPRESSA E50
IMPRESSA E55
Instructions for use
03/01
Fig. 1
Fig. 4
Fig. 7
Fig. 2
Fig. 5
Fig. 8
Fig. 3
Fig. 6
Fig. 9
2
1
Instructions for use Jura Impressa E50/E55
1. Water volume selector switch
2. Selector button for pre-ground coffee powder
3. Coffee button 2 cups
9
10
11
4. Rinsing button
5. Coffee button 1 cup
6. ON/OFF switch
8
7
7. Display with warning lamps
8. Water tank with carrying handle
9. Height-adjustable coffee-spout
10. Filler funnel for pre-ground coffee
11. Cover for bean container
12. Selector switch for coffee or hot-water/steam
13. Pivoting nozzle for hot-water/steam
14. Frothing nozzle
12
6
5
4
3
2
1
13
14
15. Container for coffee grounds
16. Drip tray cover
17. Drip tray
15
16
17
Contents
Jura Impressa E50/E55
1. Description ..................................................page
1.1 Meaning of symbols in the display.............page
2. Safety instructions........................................page
2.1 Warnings ..............................................page
2.2 Safety precautions..................................page
3. Check before use..........................................page
3.1 Checking mains voltage...........................page
3.2 Checking fuse........................................page
3.3 Filling water tank ...................................page
3.4 Adding coffee beans ...............................page
3.5 Adjusting grinder ...................................page
3.6 Adjusting for water hardness....................page
3.7 Adjustable automatic close-down ..............page
4. Preparing machine........................................page
4.1 Filling the system with water ...................page
5. Rinsing the machine......................................page
6. Adjusting water volume .................................page
6
6
6
6
7
7
7
7
7
7
7
8
9
9
9
9
9
9. Drawing off hot-water ...................................page 11
10. Switching off machine...................................page 11
11. Care and maintenance ...................................page 11
11.1 Fill water .............................................page 11
11.2 Empty ground container .........................page 11
11.3 Drip tray is missing................................page 11
11.4 Clean machine ......................................page 11
11.5 Machine furred .....................................page 12
11.6 Use of Claris filter cartridges ..................page 12
11.7 General cleaning instructions...................page 12
11.8 Regular servicing...................................page 12
11.9 Empty system.......................................page 12
12. Cleaning......................................................page 12
13. Decalcifying.................................................page 13
14. Disposal ......................................................page 14
15. Tips of a perfect coffee .................................page 14
16. Messages.....................................................page 15
17. Problems.....................................................page 17
18. Legal information .........................................page 17
19. Technical specifications .................................page 17
E
7. Drawing off espresso/normal coffee .................page 10
7.1 Drawing off espresso/strong coffee............page 10
7.2 Drawing off espresso/extra-strong coffee....page 10
7.3 Using pre-ground powder coffee ...............page 10
8. Using steam.................................................page 10
8.1 Resetting to stand-by status.....................page 11
5
1. Meaning of symbols in the display
Important information for the user
1. COFFEE READY
Thank you for choosing this Jura product.
2. COFFEE STRONG/EXTRA STRONG
3. POWDER COFFEE
4. RINSE MACHINE
5. FILL WATER
6. EMPTY GROUNDS CONTAINER/DRIP TRAY MISSING
7. CLEAN MACHINE
Please study these instructions carefully before using your new
machine and keep them in a safe place for easy reference in the
future.
Should you require further information or should particular pro-
blems occur that are not dealt with in these operating instructions
in sufficient detail for you, then please ask you local dealer for the
information you require or contact us directly.
8. MACHINE FURRED
2
3
7
4
8
1
5
1. Description
This fully-automatic espresso/coffee machine impresses because of
its compactness and can prepare 1 or 2 cups of excellent, profes-
sional-quality espresso/coffee with guaranteed froth at the same
time. The unique Jura Pre Brew Aroma System/P.B.A.S© ensures a
full coffee aroma. The machine functions fully automatically at the
press of a button. You have the choice of normal, strong or extra-
strong coffee aroma, to suit your personal preference. The integra-
ted grinder grinds beans to precisely the fineness you require. A
separate filler funnel also enables you to use an additional sort of
pre-ground coffee. The water volume is individually adjustable.
Electronic monitoring of levels in the water tank and the grounds
container simplify operations. The integrated rinsing, cleaning and
decalcifying programs facilitate care and maintenance.
6
2. Safety instructions
2.1 Warnings
Ⅲ Children are unaware of the dangers that electrical machines
represent. Therefore children should never be left alone with
electrical machines unsupervised.
Ⅲ This machine should only be used by people who have read and
understood the operating instructions.
6
3.2 Checking fuse
Ⅲ Never use a faulty machine or one with a damaged power cable.
Ⅲ Never immerse the machine in water.
The machine is designed for a current of 10 amps. Check that an
appropriate fuse is fitted.
2.2 Safety precautions
3.3 Filling water tank
Ⅲ Never expose the machine to the effects of rain, snow or frost
Ⅲ Remove water tank and rinse well with cold clean tap water.
and never operate it with wet hands.
Ⅲ Fill the tank and replace it in the machine. Ensure that the tank
clicks correctly into place (Fig. 1).
Ⅲ Place your espresso/coffee machine on a solid level surface.
Never leave it on a surface that is warm or hot (hob etc.).
Choose a location that is inaccessible for children or pets.
Note: Use only clean cold water. Never fill the tank with
milk, mineral water or any other liquid. You can also top the
tank up with water without removing it from the machine.
Simply pull up cover and pour water into the tank from
above. Put cover back in its original position.
Ⅲ Remove plug from power socket if an absence for a longer
period of time (holidays etc.) is planned.
Ⅲ Always remove plug from power socket before cleaning.
Ⅲ When removing plug from power socket, never tug on the cord
or on the machine itself.
Ⅲ Never repair or open the machine yourself. All repairs should be
performed only by authorised service centres using original Jura
spare parts and accessories.
3.4 Adding coffee beans
Ⅲ Lift up cover of the bean container (11).
E
Ⅲ Clean out any dirt or alien elements from the bean container.
Ⅲ Fill the grinder container with coffee beans and close the cover.
Ⅲ The machine is connected to the mains power socket via an
electric cable. Ensure that no one trips over this cable and
pulls down the machine. Keep children and animals away.
3.5 Adjusting grinder
Ⅲ Never put the machine or even parts of it in the dishwasher.
Ⅲ To prevent overheating put the machine in an airy place.
You can adjust the grinder to the roast of your coffee. We recom-
mend the following:
Ⅲ If you are using an acid-based descaling agent, it is important to
avoid any splashed or drips on sensitive kitchen surfaces, parti-
cularly those in natural stone or wood. If they do occur, they
should be removed immediately.
for a light roasting
for a dark roasting
©
©
a finer adjustment
a coarser adjustment
Ⅲ Open the cover of the bean container (11).
Ⅲ To adjust grinding turn selector switch (Fig. 2) to the wanted
position.
3. Check before use
3.1 Checking mains voltage
The machine is set for the correct voltage before leaving our fac-
tory. Ensure that your mains voltage corresponds to the details quo-
ted on the rating plate attached to the bottom of the machine.
7
Ⅲ You have the following possibilities to adjust the grade of grinding
the smaller the dots, the finer the grinding
the bigger the dots, the coarser the grinding
Level 2
German water hardness 8° – 15°
French water hardness 14.32° – 26.85°
Important: The grinding grade should only be adjusted while
the grinder is working.
3.6 Adjusting for water hardness
The water is heated inside the machine. With use, this leads to
calcium deposits (furring) forming on the machine. This is automa-
tically indicated in the display. For this reason, it is necessary to
adjust the machine to the hardness of your local water before you
use it for the first time. Use the enclosed test-sticks for this purpose.
Level 3
German water hardness 16° – 23°
French water hardness 28.64° – 41.14°
Note: 1° water hardness on the German scale represents
1.79° on the French scale.
Level 4
The machine has got 5 hardness settings to choose from. The
chosen grade is shown on the display.
German water hardness 24° – 30°
French water hardness 42.96° – 53.7°
Legend:
= flashes
The machine is adjusted to Level 3 before it leaves the factory.
You can alter this setting by simply following the instructions
below:
= lights up
Ⅲ Pull the mains lead with its plug out from the cable box at the
rear of the machine.
Level 0 = Setting for Claris filter
cartridges Display
Ⅲ Put the mains plug into the wall socket.
Ⅲ Leave the machine switched off.
Ⅲ Press the button
The display for automatic
decalcifying is switched off.
for about 3 seconds. Now warning lamp
(Level 3) flashes.
Ⅲ Choose the required setting by pressing button
and press
button to store in memory. The warning lamps go out.
Level 1
German water hardness 1° – 7°
French water hardness 1.79° – 12.53°
8
4. Preparing machine
Note: It is only necessary to adjust the water hardness
before the machine is used for the first time or when a diffe-
rent quality of water is used.
4.1 Filling the system with water
If no water hardness level is changed within 30 seconds, the
display goes out and the last value programmed remains
unchanged.
Ⅲ Press button
Ⅲ Warning
to switch on the machine.
lamps flash.
,
,
,
Ⅲ Place an empty cup under the pivoting nozzle (13).
Ⅲ Turn selector switch for hot-water/steam (12) to position
.
3.7 Adjustable automatic close-down
Now the machine gives off water. Warning lamps
flash. The water flow is stopped automatically.
,
You can adjust the automatic close-down of 2 hours set by Jura to
your own requirements. The machine provides 3 different levels:
Ⅲ Turn back selector switch for hot-water/steam (12) to position
.
1st Level
Warning lamp
flashes.
5. Rinsing the machine
The automatic close-down is not activated.
If warning lamp
Ⅲ Place an empty cup under the coffee-spout.
Ⅲ Press button. The rinsing is stopped automatically.
flashes, the machine needs rinsing.
2nd Level
Warning lamp
flashes, warning lamps
,
light up.
Automatic close-down is set to 2 hours.
E
Note: If the machine has been switched off and has already
3rd Level
Warning lamp
light up.
cooled down it will be necessary to carry out this rinsing
function when the machine is switched on again. After
switching off the machine, the rinsing sets off automatically.
flashes, warning lamps
,
,
,
,
Automatic close-down is set to 5 hours.
To set or alter the automatic close-down follow the instructions
below:
6. Adjusting water volume
Water volume is infinitely adjustable by means of the selector
switch (1). The small cup means a small volume of water for
espresso, the big cup means a larger volume of water for coffee. ll
cup means a small volume of water for espresso, the big cup
means a larger volume of water for coffee.
Ⅲ Put the mains plug into the wall socket.
Ⅲ Leave the machine switched off.
Ⅲ Press button
setting by pressing button
Ⅲ Push button to store level in memory
for about 3 seconds and choose the required
.
.
Tip: You can also change the water volume while coffee is
being drawn off. Simply turn the selector switch (1) to give
more or less water.
Note: If no change to the setting level is made within 30
seconds, the warning lamps go out and the last level stored
remains effective.
Note: If you press button
doubles the amount of water and divides it between two cups.
the machine automatically
9
7. Drawing off espresso/normal coffee
Ⅲ Place 1 or 2 cups under coffee-spout and press the coffee button
required.
Switch on the machine by pressing button. The machine is ready as
soon as the warning lamp
lights up.
Important: Never use soluble instant coffee or quick coffee.
Only use coffee powder from freshly ground beans or pre-
ground vacuum-packed coffee. Never fill the funnel with
more than 1 or 2 portions at a time. The powder funnel
is not intended as a storage container.
Ⅲ Place 1 or 2 cups under the coffee-spout and press the appro-
priate button. The pre-brew function (P.B.A.S©) moistens the
coffee powder, briefly interrupts the flow and then the real
brewing process begins.
Note: If button
rected by pressing button
is pressed by mistake, this can be cor-
. The machine rinses.
Note: You can interrupt the flow of coffee at any time by
simply pressing any one of the coffee buttons.
Tip: We recommend a regular cleaning of the funnel with a
bottle-brush after drawing off powder coffee.
Tip: Adjust the coffee-spout height to the size of your cups
to obtain a perfect head of froth (Fig. 3).
8. Using steam
7.1 Drawing off espresso/strong coffee
Steam can be used for heating up liquids as well as for frothing up
milk for cappuccinos. To heat up liquids remember to push the
frothing nozzle (14) up. For frothing up liquids push the nozzle
down (Fig. 5).
Ⅲ Place 1 cup under coffee-spout (9) and press the required
button until the warning lamp
flashes.
lights up. Warning lamp
Note: You can only draw off 1 cup of strong coffee at a
time.
Ⅲ Put a cup under the pivoting nozzle (13).
Ⅲ Immerse the frothing nozzle (14) into the milk you want to froth
or into the liquid you want to heat up. Turn selector switch for
7.2 Drawing off espresso/extra-strong coffee
coffee or hot-water/steam (12) to position
(Fig. 5).
Ⅲ To stop steam-function turn selector switch for coffee or hot-
Ⅲ Place 1 cup under coffee-spout (9).
water/steam (12) back to position
Ⅲ Warning lamps
.
Ⅲ Press the required button until warning lamps,
,
flash.
,
,
,
flash.
Note: You can only draw off 1 cup of extra-strong coffee at
a time.
Ⅲ If you would like to draw off coffee right after drawing off
steam, proceed as described in chapter 8.1.
7.3 Using pre-ground powder coffee
Note: The max. drawing off time for steam is about 8 minu-
tes. Due to the start frothing. This water should be drawn off
before drawing off steam. However the perfect result (e.g. of
frothing milk) is not influenced.
Ⅲ Press
button.Warning lamps
and
light up.
Ⅲ Now put 1 or 2 level measuring spoons of pre-ground coffee
(Fig. 4) into the powder funnel (10).
10
11. Care and maintenance
11.1 Fill water
Important: When steam is first drawn off, there is a possibi-
lity of spattering. The pivoting nozzle becomes hot. Avoid
direct contact with the skin.
When warning lamp
Top up water as described in chapter 3.3.
lights up no more coffee can be drawn off.
8.1 Resetting to stand-by status
Ⅲ Place a container under the pivoting nozzle (13).
11.2 Empty grounds container
Ⅲ Turn selector switch for hot-water/steam (12) to position
Ⅲ Push button and draw off water until water-flow is automa-
tically stopped. Warning lamps flash.
Ⅲ Then turn back selector switch for hot-water/steam (12) to posi-
.
Coffee grounds are collected in the grounds container. When
warning lamp
lights up, all coffee buttons are blocked and you
,
,
,
must empty the grounds container.
Ⅲ Push up coffee-spout (9).
tion
.
Ⅲ Remove drip tray. Do this carefully as there is water in it.
Tip: Whenever you have finished drawing off steam clean
the pivoting nozzle with a damp cloth.
Ⅲ Remove and clean drip tray (Fig. 6) and grounds container. First
replace grounds container and then drip tray (Fig. 7).
9. Drawing off hot-water
Important: Whenever grounds container is emptied, empty
drip tray too.
Ⅲ Place a cup under the pivoting nozzle (13) and turn selector
E
switch for hot-water/steam (12) to the symbol
Ⅲ Press button . The machine will now deliver hot-water.
Ⅲ To stop this process turn back selector switch for hot-water/
steam (12) to the sympol
.
11.3 Drip tray is missing
If the drip tray is not replaced correctly, warning lamp
flashes.
.
Note: When the drip tray is outside the machine you can take
the opportunity to clean the inside of the machine. Wipe off
any of coffee powder with a damp cloth. Then replace clean
drip tray.
Important: When hot-water and steam are first drawn off,
there is a possibility of spattering. The pivoting nozzle beco-
mes hot. Avoid direct contact with the skin.
11.4 Clean machine
10. Switching off machine
After coffee etc. has been drawn off 200 times or 160 rinse
programs have been run, the machine must be cleaned. Warning
When the machine is switched off, the rinsing program is auto-
matically run again. Place an empty cup under the coffee-spout and
press button. When the rinsing water has run into the cup, the
machine powers down. Discard the water.
lamp
will remind you. You can still draw off coffee and hot-
water/steam. However we recommend that you clean the machine
(as described in chapter 12) within the next few days. Warning
lamp
does not go out until the complete cleaning process has
been carried out.
11
11.5 Machine furred
11.8 Regular servicing
Your machine will become furred in the course of normal use. The
amount of furring depends on the hardness of your water. The ma-
chine registers when descalcifying becomes necessary and signals
this via warning lamp . You can still draw off coffee and hot-wa-
ter/ steam. However we recommend that you decalcify the machine
(as described in chapter 13) within the next few days. Warning
lamp does not go out until the complete decalcifying process has
been carried out.
Regular Jura services ensure your machine’s reliability and longer
life. Keep the original packaging to protect the machine when it is
transported.
11.9 Empty system
Important: This process is necessary to protect the machine
from frost damages while being transported.
Ⅲ Press button
to switch off the machine.
11.6 Use of Claris filter cartridges
Ⅲ Place a container under the pivoting nozzle (13)
At the correct use of Claris filter cartridges, decalcifying of the
machine becomes unnecessary. For further information, please read
the instructions for use attached to the water tank.
Ⅲ Turn selector switch for hot-water/steam (12) to position
.
Ⅲ Press button
to switch on the machine. Warning lamps
flash.
until only warning lamp
,
,
,
Note: Furring display must be switched off (as described in
chapter 3.6) before using Claris filter cartridges.
Ⅲ Press button
comes out after a short time.
flashes. Steam
Ⅲ Draw off steam until it stops automatically.
11.7 General cleaning instructions
Ⅲ Turn selector button for hot-water/steam (12) back to position
.
Ⅲ Never use sharp or abrasive articles or corrosive chemicals to
clean your machine.
12. Cleaning
Ⅲ Wipe down the casing inside and out using a soft damp cloth.
Ⅲ Clean the pivoting hot-water/steam nozzle every time it is used.
The machine has an integrated cleaning program.
Ⅲ After warming milk, draw off a little hot-water to clean the
pivoting nozzle inside.
Note: Whenever the machine needs cleaning, warning lamp
lights up. You can still draw off coffee and hot-water/
steam and run the cleaning program later.
Only use Jura cleaning tablets. These are available from your
Jura dealer.
Ⅲ You can take off the pivoting nozzle for a thorough cleaning
(Fig. 8).
Ⅲ The water tank should be rinsed out and filled with clean water
daily.
Important: It is essential not to interrupt the process once it
has been started.
Note: If you notice any furring in the water tank, this can be
descalcified separately with a customary decalcifying pro-
duct. Remove the tank from the machine in order to do this.
12
Tip: Clean powder funnel with a bottle-brush.
Ⅲ Switch on machine by pressing
button.
Ⅲ Push button
(if necessary)
for about 3 seconds. Warning lamps
light up.
,
,
13. Decalcifying
Ⅲ Fill water tank.
Your machine has an integrated decalcifying program. If a Claris fil-
ter cartridge is used there is no need for decalcifying your machine.
Please use Jura decalcifying tablets only. These are available from
your Jura dealer
Ⅲ Empty drip tray and grounds container and replace them. War-
ning lamps (if necessary) go out.
Ⅲ Place a container under the coffee-spout (9).
Ⅲ Put a Jura cleaning tablet (Fig. 9) into the powder funnel (10).
Ⅲ Press selector button
. The warning lamp
goes out.
Note: If the machine needs decalcifying warning lamp
lights up. You can still draw off coffee and hot-water/steam
and run the decalcifying program later.
Warning lamp
flashes.
The flashing of warning lamp
process is activated.
indicates that the cleaning
Important: Run the decalcifying program only after the ma-
chine has been switched off for at least 2 hours and has
cooled down completely. The decalcifying program is started
with the machine switched off. The running decalcifying
program must not be interrupted.
Ⅲ If warning lamp
lights up, empty drip tray (if necessary),
wait about 10 seconds before replacing it. Warning lamp
goes out.
Ⅲ Replace the container under the coffee-spout (9) and press button
Ⅲ Switch off machine by pressing button
cool down for 2 hours.
and let the machine
E
.
Ⅲ Then remove water tank.
The cleaning process is continued.
Ⅲ Press button
for about 3 seconds. Warning lamps
,
,
Ⅲ If warning lamp
lights up again, empty drip tray (if neces-
light up.
sary), wait about 10 seconds before replacing it. Warning lamp
goes out.
Ⅲ Pour 0,5 litres of water into a container and completely dissolve
the contents of a blister pack (2 tablets). Then fill the mixture in-
to the water tank.
Ⅲ Replace the container under the coffee-spout (9) and press button
.
Ⅲ Empty drip tray and replace it. Warning lamps
,
,
,
flash and warning lamp lights up.
The cleaning process is continued. At the end of it, warning lamp
lights up.
Ⅲ Place a sufficiently big container under the pivoting nozzle (13).
Turn selector switch for hot-water/steam (12) to position
.
Ⅲ Empty drip tray and grounds container and replace them.
Warning lamp
Ⅲ Replace container under the coffee spout (9) and press button
. The machine rinses and warning lamp lights up.
lights up.
13
The decalcifying program is continued and the decalcifying soluti-
on is channelled inside the machine to the drip tray.
The flashing of warning lamp
program is activated.
indicates that the decalcifying
Ⅲ Warning lamp
flashes, warning lamps
,
light up.
Ⅲ If warning lamp
Warning lamps
lights up.
lights up, empty drip tray (if necessary).
flash and warning lamp
,
,
,
Ⅲ Empty drip tray and replace it.
Ⅲ Then press button
draw off coffee.
. Your machine rinses and is ready to
Ⅲ Turn selector switch for hot-water/steam (12) back to position
.
14. Disposal
The decalcifying program is continued and the decalcifying soluti-
on is channelled inside the machine to the drip tray.
For correct disposal, you should return your coffee machine to your
dealer, Jura service centre or Jura Elektroapparate AG.
Ⅲ Warning lamp
flashes and warning lamps
,
,
, light
up.
15. Tips for a perfect coffee
Ⅲ Important: Fill water tank with fresh water and replace it.
Ⅲ Empty drip tray (if necessary) and replace it. Warning lamps
flash and warning lamp lights up.
Ⅲ Put a sufficiently big container under the pivoting nozzle (13).
Turn selector switch for hot-water/steam (12) to position
Warning lamps flash.
Height adjustable coffee-spout
You can adjust the height of the coffee-spout to your cup sizes.
,
,
,
Grinding
.
Please see chapter 3.5.
,
Pre-warm cups
The decalcifying program is continued.
You should warm cups in advance with hot water or steam. The
smaller the quantity of coffee, the more important warming the
cups is.
Ⅲ Warning lamp
Ⅲ Empty drip tray (if necessary) and replace it. Warning lamps
flash and warning lamp lights up.
Ⅲ Turn selector switch for hot-water/steam (12) back to position
. Warning lamps flash.
flashes and warning lamps
,
light up.
,
,
,
Sugar an cream
Warmth is lost by stirring the contents of the cup. Adding milk or
cream from the refrigerator considerably lowers the temperature of
the coffee.
,
14
16. Messages
Display
Cause
Action
System empty
Fill the system (see chapter 4.1)
Re-set to coffee ready
Re-set to correct position
System too hot after drawing off steam
Selector switch in wrong position
General troubles
1. – Switch off
– Disconnect from mains power
– Connect machine to mains power
– Switch on machine
2. Have the machine checked at a Jura service centre
Rinsing the machine
Machine needs rinsing
E
Water tank empty
Float faulty
Fill water tank
Rinse out tank, descalcify tank if necessary
Grounds container full
Empty grounds
Drawer replaced too early
Wait at least 10 seconds and replace drawer
Drip tray not inserted properly or missing
Replace correctly
15
Display
Cause
Action
Cleaning necessary
Run cleaning program
Decalcifying necessary
Run decalcifying program
17. Problems
Problem
Cause
Action
Coffee flow is stopped after
pre-brewing
– Beans container is empty
– Not enough coffee powder
– Fill in beans
– Measure powder correctly
Grinder is extremely noisy
– Alien element in grinder
– Drawing off powder coffee is still possible
– Have the machine checked at a Jura service centre
Not enough froth
– Unsuitable milk-type
– Use full cream milk
– Frothing nozzle blocked
– Frothing nozzle in wrong
– Clean frothing nozzle
– Drawing off steam (see chapter 8)
If none of the remedies listed above help, please contact your dealer or get in touch with Jura Elektroapparate AG.
16
18. Legal information
19. Technical specifications
These operating instructions contain all the information necessary
for the correct use, operation and maintenance of your espresso/
coffee machine.
Voltage:
230 V AC
1350 W
10 A
Power consumption:
Fuse:
Volume of water tank: 1,9 litre
Weight: 8,3 kg
Understanding and complying with the directions contained in
these operating instructions are essential to ensure that the machi-
ne is utilised without risk and to ensure safety during operation and
maintenance.
These operating instructions cannot cover all the possible ways in
which this machine may be used. This machine has been designed
for private use in households.
Dimensions (WxHxD): 28 x 34,5 x 41,5 cm
Safety standards:
We would further point out that the contents of these operating in-
structions in no way constitute a part of, or alter, any previous or
existing contract, agreement or legal relationship. All obligations
on the part of Jura Elektroapparate AG result solely from the rele-
vant sales agreement which also contains full details of the only
warranty terms valid in respect of this machine. The contractual
terms of this warranty are neither extended not limited in any form
by the information in these operating instructions.
These operating instructions contain information that is protected
by copyright. The photocopying or translation into any other lan-
guage of these instructions without prior written authorisation from
Jura Elektroapparate AG is strictly prohibited.
E
17
|