Oregon Scientific Clock EMR801 User Manual

2. Wall mount hole  
3. Battery compartment  
4. RESET hole  
Thermomètre extérieur et intérieur  
sans fil à horloge numérique  
Modèle : EMR801  
TIME AND INDOOR TEMPERATURE DISPLAY  
ABOUT OREGON SCIENTIFIC  
To enable auto-toggle display of time and indoor  
temperature:  
more about Oregon Scientific products. If you’re in the US  
and would like to contact our Customer Care department  
directly, please visit: www2.oregonscientific.com/service/  
support  
5. CHANNEL switch  
Press and hold  
for 2 seconds.  
Wireless Indoor and Outdoor  
Thermometer with Digital Clock  
Model: EMR801  
Manuel de l’utilisateur  
To disable auto-toggle display of time and indoor  
temperature:  
For international inquiries, please visit:  
GETTING STARTED  
SOLAR PANEL  
www2.oregonscientific.com/about/international  
Press MODE.  
FR  
The solar panel is an energy saving feature, which is an  
environmentally friendly way to provide additional power to  
the main unit and prolongs battery life. However, it cannot  
replace battery power entirely.  
VUE D’ENSEMBLE  
To manually toggle between time and indoor  
temperature display:  
FCC STATEMENT  
USER MANUAL  
FACE AVANT  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) This  
device may not cause harmful interference, and (2) This  
device must accept any interference received, including  
interference that may cause undesired operation.  
Press MODE.  
EN  
1
OVERVIEW  
INSERT BATTERIES  
ICE WARNING  
FRONT VIEW  
1. Remove the battery compartment.  
2. Insert the batteries, matching the polarities.  
3. Press RESET after each battery change.  
If the sensor falls between 3°C to -2 °C (37°F to 28°F), the  
green LED indicator will flash, and will stop flashing once  
the temperature is out of this range.  
WARNING Changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user’s authority to operate the equipment.  
1
9
8
2
MEANING  
LOCATION  
NOTE As ice alert is only applicable to channel 1, to  
prevent flashing of LED, select channel 2 or 3 on outdoor  
sensor.  
Indoor temperature / time  
area  
Main unit batteries low  
NOTE This equipment has been tested and found  
to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful  
interference in a residential installation.  
7
3
9
8
Outdoor temperature area  
Sensor batteries low  
2
3
RESET  
4
SET CLOCK  
Press RESET to return to the default settings.  
6
5
7
6
1. Press and hold MODE for 2 seconds.  
2. Press to change values.  
This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there  
PRECAUTIONS  
3. Press MODE to confirm.  
4
5
Do not subject the unit to excessive force, shock, dust,  
temperature or humidity.  
1. Panneau solaire  
4. The settings order is: 12/24 hour format, hour and  
minute.  
is no guarantee that interference will not occur in  
a
2. Température extérieure  
particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or  
more of the following measures:  
Do not cover the ventilation holes with any items such  
as newspapers, curtains etc.  
3. Température intérieure / heure  
4. Indicateur d’alerte du niveau de gel  
REMOTE SENSOR  
To set up the sensor:  
Do not immerse the unit in water. If you spill liquid over  
it, dry it immediately with a soft, lint-free cloth.  
5.  
: Augmente la valeur, alternance automatique de  
l’heure et de la température intérieure  
1. Solar panel  
Do not clean the unit with abrasive or corrosive  
materials.  
1. Open the battery compartment and insert the battery,  
matching the polarity.  
Reorient or relocate the receiving antenna.  
2. Outdoor temperature  
3. Indoor temperature / Time  
4. Ice alert indicator  
6. MODE : Permet d’entrer dans le mode Réglages,  
Increase the separation between the equipment and  
receiver.  
d’alterner entre l’heure et la température intérieure  
Do not tamper with the unit’s internal components.  
This invalidates the warranty.  
2. Press RESET.  
7. Indicateur de faiblesse des piles de l’appareil  
principal  
3. Close the battery door.  
Connect the equipment into an outlet on a circuit  
different from that to which the receiver is  
connected.  
5.  
: Increase value ; auto-toggle of indoor temperature  
and time  
Only use fresh batteries. Do not mix new and old  
batteries.  
4. Place the sensor within 30 m (98 ft) of the main  
unit using the table stand , mounting magnet or wall  
mount.  
8. Indicateur de faiblesse de la pile de la sonde sans fil  
9. Indicateur de réception de la sonde sans fil  
6. MODE: Enter setting mode; toggle between indoor  
Images shown in this manual may differ from the  
actual display.  
temperature and time  
Consult the dealer or an experienced radio / TV  
technician for help.  
7. Main unit low battery indicator  
When disposing of this product, ensure it is collected  
separately for special treatment.  
TIP Ideal placements for the sensor would be in any  
location on the exterior of the home at a height of not more  
than 1.5 m (5 ft) and which can shield it from direct sunlight  
or wet conditions for an accurate reading.  
FACE ARRIERE  
8. Remote sensor low battery indicator  
9. Remote sensor reception indicator  
Placement of this product on certain types of wood  
may result in damage to its finish for which Oregon  
Scientific will not be responsible. Consult the furniture  
manufacturer’s care instructions for information.  
DECLARATION OF CONFORMITY  
The following information is not to be used as contact  
for support or sales. Please visit our website at www2.  
oregonscientific.com/service for all enquiries.  
1
2
BACK VIEW  
The contents of this manual may not be reproduced  
without the permission of the manufacturer.  
We  
Name:  
Address:  
Oregon Scientific, Inc.  
19861 SW 95th Ave.,Tualatin,  
Oregon 97062 USA  
Do not dispose old batteries as unsorted municipal  
waste. Collection of such waste separately for special  
treatment is necessary.  
1
2
6
5
3
4
Telephone No.:  
1-800-853-8883  
Please note that some units are equipped with a  
battery safety strip. Remove the strip from the battery  
compartment before first use.  
declare that the product  
Product No.:  
EMR801  
1.5 m (5 ft)  
Product Name:  
Wireless Indoor and Outdoor  
Thermometer with Digital Clock  
IDT Technology Limited  
Block C, 9/F, Kaiser Estate,  
Phase 1,41 Man Yue St.,  
Hung Hom, Kowloon,  
NOTE The technical specifications for this product and  
the contents of the user manual are subject to change  
without notice.  
6
5
3
4
Manufacturer:  
Address:  
NOTE Features and accessories will not be available  
in all countries. For more information, please contact your  
local retailer.  
1. Trou de fixation murale  
2. Aimant de montage  
Hong Kong  
3. °C / °F : Permet de sélectionner l’unité de mesure de  
is in conformity with Part 15 of the FCC Rules.Operation is  
subject to the following two conditions: 1) This device may  
not cause harmful interference.2) This device must accept  
any interference received, including interference that may  
cause undesired operation.  
la température  
NOTE Use alkaline batteries for longer usage and  
consumer grade lithium batteries in temperatures below  
freezing.  
SPECIFICATIONS  
4. Compartiment des piles  
5. Support de table  
1. Wall-mount hole  
TYPE  
DESCRIPTION  
2. Mounting magnet  
6. RESET (REINITIALISER) : Réinitialise l’appareil aux  
MAIN UNIT  
L x W x H  
3. °C/°F: Select temperature unit  
4. Battery compartment  
5. Table stand  
réglages par défaut  
SENSOR DATA TRANSMISSION  
To search for a sensor:  
68 x 24 x 96 mm  
(2.68 x 0.94 x 3.78 in)  
Press and hold MODE +  
for 2 seconds.  
SONDE SANS FIL  
Weight  
80 g (2.82 oz) without battery  
-5°C to 50°C (23°F to 122°F)  
433 MHz  
6. RESET: Reset unit to default settings  
The sensor reception icon in the remote sensor area  
shows the status:  
Temperature range  
Signal frequency  
Power  
2
REMOTE SENSOR  
ICON  
DESCRIPTION  
2 x UM-4 (AAA)  
1.5 V batteries  
1
Main unit is searching  
for sensor(s).  
OUT  
OUT  
2
4
5
REMOTE UNIT (THN132N)  
3
OUT  
OUT  
OUT  
OUT  
A channel has been  
found.  
1
L x W x H  
96 x 50 x 22 mm  
(3.78 x 1.97 x 0.87 in)  
4
5
The sensor cannot be  
found.  
OUT  
3
Weight  
62 g (2.22 ounces)  
1. Indicateur de statut LED  
Transmission range  
Temperature range  
Power  
30 m (98 ft) unobstructed  
-20°C to 60°C (-4°F to 140°F)  
1 x UM-3 (AA) 1.5 V batteries  
2. Trou de fixation murale  
3. Compartiment des piles  
4. Fente RESET (Réinitialiser)  
5. Bouton CHANNEL (CANAL)  
TIP The transmission range may vary depending on  
many factors. You may need to experiment with various  
locations to get the best results.  
1. LED status indicator  
 

Miele Clothes Dryer 10 000 750 User Manual
Murphy Automobile Parts RP2307B User Manual
NAD Stereo Amplifier 208THX User Manual
National Instruments Network Card SCC AO10 User Manual
NEC Computer Hardware uPD75P3116 User Manual
Nilfisk ALTO Vacuum Cleaner BA 410 User Manual
NordicTrack Treadmill NTL14942 User Manual
Nuvo MP3 Docking Station NV RIPR1 User Manual
Omega Vehicle Security Battery Charger SMCJ J User Manual
Panasonic Fax Machine KX FPC96 User Manual