Harbor Freight Tools WORKSTAND 95365 User Manual

bicycle workstand  
150 lb. capacity  
Model 95365  
asseMbly and operation instructions  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
to preVent serious injury, read and understand  
all warnings and instructions before use.  
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
for technical questions or replacement parts, please call 1-800-444-3353.  
unpacking  
When unpacking, check to make sure that the item is intact and undamaged. If any  
parts are missing or broken (see parts list/assembly diagram), please call Harbor Freight  
Tools at the number shown on the cover of this manual as soon as possible.  
asseMbly instructions  
note: For additional information regarding the parts listed in the following pages, refer to  
the Assembly Diagram on page 6 of this manual.  
The Bicycle Workstand can be easily assembled by taking the following steps. The Work-  
stand will stand on its own and will hold up to 150 Lbs, evenly distributed.  
1.  
Set one Leg Assembly A (9) and Leg Assembly B (11) on each side of the Post (2)  
so that the holes line up with the holes at the bottom of the Post (2). Through the  
lowest hole, insert Screw (8) and thread on Nut (12)-see Figure 1. Through the next  
hole up, insert the Screw (8) from the opposite direction and thread on Nut (12)-see  
Assembly Diagram. Attach Leg Covers (10) to the end of each leg (not shown in  
Figure 1).  
Post (2)  
Leg Cover (10)  
Nut (12)  
Screw (8)  
Screw (8)  
Nut (12)  
Leg Assy A  
(9)  
Leg Assy B (11)  
Figure 1  
2.  
Slide the Bottom Support Assembly Brace (7) down over the Post (2) until it is at  
the adjustment holes. Set the Bottom Support Assembly Holder (4) and the Bottom  
Support Assembly Brace (7) so that they line up on each side of the desired hole.  
Thread the Handle Wheel (13) into the Bottom Support Assembly Brace (7). Slide  
Washer (5) onto the threaded end of the Handle Wheel (13) and thread on Nut (6)  
to secure it in place-see Figure 2.  
SKU 95365  
for technical questions, please call 1-800-444-3353.  
Page 3  
Bottom Support  
Assembly Brace (7)  
Bottom Support  
Assembly Holder (4)  
Nut (6)  
Handle Wheel (13)  
Washer (5)  
Figure 2  
3.  
Attach the Top Support Assembly (15) to the top two holes on the Post (2). Secure  
in place using two Screws (3)-see Figure 3.  
Top Support  
Assembly (15)  
Screw (3)  
Figure 3  
operation instructions  
1.  
2.  
Position the Workstandin a location where it will not be an obstruction to passersby.  
Place it on a smooth, flat and level surface capable of supporting the Workstand  
and the weight of the bicycle and components.  
The Bottom Support Assembly Holder is adjustable. Set the Bottom Support As-  
sembly Holder (4) to the desired height. With the bicycle upside down, set the top  
tube (flat horizontal tube nearest the seat) of the bicycle onto the Bottom Support  
Assembly Holder (4). Rest the bottom of the bicycle in the Top Support Assembly  
(15).  
inspection, Maintenance, and cleaning  
1.  
before eacH use, inspect the general condition of the tool. Check for loose  
screws, misalignment or binding of moving parts, cracked or broken parts, and any  
other condition that may affect its safe operation. do not use damaged equip-  
ment.  
SKU 95365  
for technical questions, please call 1-800-444-3353.  
Page 4  
parts list  
part  
description  
Q’ty part  
description  
Leg Assembly A  
Leg Cover  
Q’ty  
1
2
3
4
5
6
7
Cover  
Post  
4
1
2
1
6
3
1
9
2
1
2
2
1
1
1
10  
11  
12  
13  
14  
15  
Screw  
Leg Assembly B  
Nut  
Bottom Support Assy Holder  
Washer  
Handle Wheel  
Nut  
Nut  
Bottom Support Assy Brace  
Top Support  
Assembly  
please read tHe following carefully  
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND ASSeM-  
BLY DIAgRAM IN THIS MANUAL AS A ReFeReNCe TOOL ONLY. NeITHeR THe MANUFACTUReR  
OR DISTRIBUTOR MAKeS ANY RePReSeNTATION OR WARRANTY OF ANY KIND TO THe BUYeR  
THAT He OR SHe IS qUALIFIeD TO MAKe ANY RePAIRS TO THe PRODUCT, OR THAT He OR  
SHe IS qUALIFIeD TO RePLACe ANY PARTS OF THe PRODUCT. IN FACT, THe MANUFACTUReR  
AND/OR DISTRIBUTOR eXPReSSLY STATeS THAT ALL RePAIRS AND PARTS RePLACeMeNTS  
SHOULD Be UNDeRTAKeN BY CeRTIFIeD AND LICeNSeD TeCHNICIANS, AND NOT BY THe  
BUYeR. THe BUYeR ASSUMeS ALL RISK AND LIABILITY ARISINg OUT OF HIS OR HeR RePAIRS  
TO THe ORIgINAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARISINg OUT OF HIS  
SKU 95365  
for technical questions, please call 1-800-444-3353.  
Page 5  
asseMbly diagraM  
SKU 95365  
for technical questions, please call 1-800-444-3353.  
Page 6  

Aiphone Camera Accessories KCW M User Manual
Alpine 68 16909Z79 A User Manual
Attwood 69371 User Manual
Directed Audio 2300X User Manual
Dual ILLUMINITE TS10 User Manual
Dual XDMA6855 User Manual
Falcon MONITORING F110 User Manual
Hitachi VM H825LA User Manual
Humax HATHWAY ND 1000C User Manual
JVC Car Speaker CS HX636 User Manual