ATN Inc Binoculars ATN PS 22 User Manual

ATN PS-22  
NIGHT VISION ATTACHMENT  
u s e r ` s g u i d e  
Important Export Restrictions! Commodities, prod-  
ucts, technologies and services contained in this manual  
are subject to one or more of the export control laws and  
regulationsoftheU.S. Governmentandtheyfallunderthe  
control jurisdiction of either the US Department of State  
or the US BIS-Department of Commerce. It is unlawful  
and strictly prohibited to export, or attempt to export or  
otherwise transfer or sell any hardware or technical data  
or furnish any service to any foreign person, whether  
abroad or in the United States, for which a license or writ-  
ten approval of the U.S. Government is required, without  
first obtaining the required license or written approval  
from the Department of the U.S. Government having  
jurisdiction. Diversion contrary to U.S. law is prohibited.  
 
APPLICATION  
The PS-22 is attachment for daytime riflescopes with 1x-6x (2.5x-4x are optimal) magnification that  
converting scope into a high quality, very accurate night vision weapon sight.  
The PS-22 mounts in front of daytime scope. Re-zeroing of scope not required. PS-22 comes standard  
with 7/8” weaver mount. There is also Adapter for ARMS quick release mount. Optional Ring Adapters  
allows to mount unit onto the objective of the day scope (25...58mm diameter). The IR illuminator can be  
mounted onto the optional Picatinny Rail.  
The PS-22 utilizes a 2nd Gen.+ or 3rd Gen. Image Intensifier Tube. This ingenious setup allows the  
shooter to go from day to night in less then 30 seconds without tools, without changes in eye relief and  
remain zeroed all around the clock.  
The PS-22 is a complex optical-electronic system. The device contains an image intensifier tube as-  
sembly with an integrated high voltage power source and the three volt battery housing.  
Objective lens protective cover is intended to protect objective lens from dust, scratches and high-level  
illumination. The pinhole in cover allows the user to check the operation ability of the device in highlight  
conditions.  
The device has a built in Automatic Brightness Control. This system automatically adjusts the bright-  
ness of Image Intensifier Tube to the optimal level.  
The Automatic Highlight Protective System analyzes light exposure. If high light exposure is kept more  
than 10 seconds the device automatically will off.  
NOTE: The automatic highlight protective system and automatic brightness control system do not pro-  
tect a sight from damage by bright light sources (a fire, headlights of the automobile, lanterns, etc.). Do  
not point the device at a bright light source.  
FEATuRES  
• Easily changes daytime scope to Night Vision  
• Mounts in front of daytime scope, no re-zeroing required  
• Available in 2nd + and 3rd generation  
• Multi-coated all glass optics  
• Fast catadioptic front lens system  
• Large 40mm eyepiece/output window  
• Light weight and rugged  
• Comes standard with 7/8” weaver mount  
• Adapter for ARMS quick release mount included  
• Optional adapters for mountinng onto the objective of the day scope (25...58mm diametr)  
SPECIFICATIONS  
Magnification...................................................................................................................1X  
Intensifier Tube.................................................................................. 2nd Gen+ or 3rd Gen  
Lens System............................................................................................... F1:1.44, 80mm  
FOV ................................................................................................................................13°  
Power Supply ..........................................................................one 3 Volt Battery(CR123A)  
Range Of Focus ............................................................................................10m to Infinity  
Battery Life............................................................................................................50 hours  
Operating Temperature...............................................................................-40°C to +50°C  
Waterproof................................................................................................... 10m for 30min.  
Dimensions .................................................................................139mm X 80mm X 72mm  
Weight ........................................................................................................................ 0.6kg  
2
 
MOuNTING  
Mounting onto the Weaver rail with 7/8”  
Weaver Mount  
1) Mount the 7/8” Weaver Mount onto the body of  
PS-22 with 2 screws M4x7 from set.  
2) Unscrew the protective back cap from PS-22.  
3) Screw the Light Screen into the thread in back  
side of unit.  
4) Slightly loosen the fixing screws of mount.  
5) Place the PS-22 on the weaver rail of the fire  
arm before objective of daytime scope on the  
minimal distance from it. The optical axes of PS-  
22 and daytime scope must have divergence not  
more than 3mm. High of optical axe of the PS-22  
under weaver rail is 40mm with standard mount  
and corresponded ATN 3.5x26 scope.  
6) Tighten the fixing screws.  
NOTE: Fixing screws may need to be tightened  
after continuous shooting.  
Mounting onto the Weaver rail with A.R.M.S.  
Mount  
1) Mount the Adapter onto the body of PS-22 with  
2 screws M4x7 from set.  
2) Mount the PS-22 with Adapter onto the  
A.R.M.S.#10 or A.R.M.S.#19 ACOG with 2  
screws M5x8.  
3) Unscrew the protective back cap from PS-22.  
4) Screw the Light Screen into the thread in back  
side of unit.  
5) Slightly loosen the fixing screws or levers of  
mount.  
6) Place the PS-22 on the weaver rail of the fire  
arm before objective of daytime scope on the  
minimal distance from it. The optical axes of PS-  
22 and daytime scope must have divergence not  
more than 3mm. High of optical axe of the PS-22  
under weaver rail is 49mm with A.R.M.S.#19  
ACOG.  
7) Tighten the fixing screws or levers of mount.  
NOTE: Fixing screws may need to be tightened  
after continuous shooting.  
Mounting onto the objective of the day scope  
with Optional Ring Adapters  
1) Unscrew the protective back cap from PS-22.  
2) Screw the Ring Adapter into the thread in back  
side of unit.  
3) Slightly loosen the fixing screws of Ring  
Adapter.  
4) Put the Insert into the Adapter  
3
 
5) Slide the PS-22 with Adapter onto the objective of day scope.  
6) Tighten hard the fixing screws of the Ring Adapter.  
7) Mount the Picatinny Rail Adapter onto the body of PS-22 with 2 screws M4x7 from set.  
8) Place the IR Illuminator onto the Picatinny Rail.  
Optional Ring Adapters allows to mount unit onto the objective of the day scope  
(25...58mm diameter)  
Ring Adapter #  
1
Diametr of scope lens  
(insert size)  
Examples of scops  
25.4  
30  
Leupold 1,5-5x20 PR  
Leupold 1,5-5x20 MR/T M2,  
Zeiss 1,1-4x24 T  
2
3
38  
42  
Meopta Artemis 2000 4x32  
Leupold 3-9x36,  
Kahles 4x36  
46.5  
48  
Leupold 3,5-10x40  
Zeiss1,5-6x42,  
Swarovski PV-N 2,5-10x42  
fro 48.7 to 49.0  
Meopta Artemis 3000 3-9x42  
Meopta Artemis 3000 4-12x40  
Schmidt@Bender 10x42 PMII  
Zeiss 2,5-10x50  
49.5  
50  
4
56  
57  
Schmidt@Bender 3-12x50  
Leupold 4,4-14x50  
58.4  
OPERATION  
• Place the PS-22 before objective of daytime scope.  
• Put power switch in OFF-position.  
• Install the battery into the housing with the polarity order as shown on the devices body. The bat-  
tery is 3 volt lithium battery (CR123A).  
• Turn the devise on by rotation the power switch into the ON-position. The greenish-lit screen of  
the image tube (when looking through the eyepiece) means that the image tube is powered.  
Do not turn the unit on in the daytime without the protective lens cap on.  
• Next, remove the lens cap.  
• Observe the scene and adjust the focusing of PS-22 by rotation the focusing ring. Also focusing  
daytime scope for optimal clarity.  
• Turn on the illumination of day scope reticle (if it present) and adjust the brightness.  
• Put power switch in OFF-position for turn PS-22 off.  
4
 
WARNINGS AND CAuTIONS  
• Always remember to turn off the PS-22 when it is not in use. If you do not plan on using your unit for  
a period of more than 10 days, you should remove the batteries.  
• Keep lens cap on when not in use.  
• Avoid contact with dust, steam, and gas.  
• The PS-22 is not harmful to the user or the environment.  
• Do not disassemble: it will void your warranty.  
• Never use in daylight without the lens cap on.  
Never point the PS-22 at a bright light source. If the scope shuts off automatically after directing it  
at a bright light source, turn the unit off and wait 1 - 2 minutes before turning the unit back on.  
• Adverse atmospheric conditions such as fog, smog, or haze and a lack of ambient light (moon or  
starlight) may diminish the effective viewing distance. All technical data for this unit was compiled  
in a controlled environment.  
TROubLE SHOuTING  
Q: Flashes, flickers or clicking occur while operating  
S: If it occurs within the first five minutes of inserting new batteries, it is normal and the device will  
resume normal operation soon thereafter. If it occurs for more than 10 minutes, contact for service  
instructions.  
Q: Dark spots on screen.  
S: These are either cosme tic blemishes in the intensifier tube or dust particles.  
Q: Screen becomes darker than at previous use.  
S: Replace batteries. If problem persists, contact your dealer or other authorized service representa-  
tive for service instructions.  
Q: Image not clear.  
S: Adjust objective lens, and/or the eyepiece.  
5
 
ATN LIMITED LIFETIME WArrANTy  
LIMITATIoN oF LIAbILITy  
ATN Limited Lifetime Warranty is limited to the  
product being free of manufacturer defects  
in materials and workmanship. In regards to  
night vision products the image intensifier  
tube is warranted to be free from manufacturer  
defects for a period of 2 years (defects do not  
include minor black spots or blemishes in view-  
ing area). ATN will repair or replace said prod-  
ucts or part thereof which upon inspection by  
ATN are found to be defective in materials or  
workmanship. As a condition to the obligation  
of ATN to repair or replace said product, the  
product must be returned to ATN together with  
proof-of-purchase satisfactory to ATN. This  
warranty does not cover damages caused by  
misuse or improper handling. This warranty is  
null and void if modification or maintenance is  
provided by parties other than ATN Corp. In the  
event a defect that is covered by the foregoing  
warranty occurs during the applicable period  
stated above, ATN, at its option, will either re-  
pair or replace the product, and such action on  
the part of ATN shall be the full extent of ATN’s  
liability, and the Customer’s sole and exclu-  
sive remedy. This warranty does not cover a  
product (a) used in other than its normal and  
customary manner; (b) subjected to misuse;  
(c) subjected to alterations, modifications or  
repairs by the Customer of by any party other  
than ATN without prior written consent of ATN;  
(d) special order or “close-out” merchandise  
or merchandise sold “as-is” by either ATN or  
the ATN dealer; or (e) merchandise that has  
been discontinued by the manufacturer and  
either parts or replacement units are not avail-  
able due to reasons beyond the control of ATN.  
ATN shall not be responsible for any defects or  
damage that in ATN’s opinion is a result from  
the mishandling, abuse, misuse, improper  
storage or improper operation, including use  
in conjunction with equipment which is electri-  
cally or mechanically incompatible with or of  
inferior quality to the product, as well as fail-  
ure to maintain the environmental conditions  
specified by the manufacturer. CuSTOMER  
IS HEREbY NOTIFIED THAT OPERATION  
OF THE EQuIPMENT DuRING DAYLIGHT  
HOuRS OR uNDER ANY EXCESSIVE LIGHT  
CONDITIONS MAY PERMANENTLY DAM-  
AGE THE INTERNAL COMPONENTS OF  
THE uNIT AND SAID DAMAGE WILL NOT  
bE COVERED uNDER THIS WARRANTY.  
This warranty is extended only to the original  
purchaser. Any breach of this warranty shall be  
waived unless the customer notifies ATN at the  
address noted below within the applicable war-  
ranty period.  
ATN will not be liable for any claims, actions,  
suits, proceedings, costs, expenses, dam-  
ages or liabilities arising out of the use of this  
product. Operation and use of the product are  
the sole responsibility of the Customer. ATN’s  
sole undertaking is limited to providing the  
products and services outlined herein in ac-  
cordance with the terms and conditions of this  
Agreement. The provision of products sold and  
services performed by ATN to the Customer  
shall not be interpreted, construed or regard-  
ed, either expressly or implied, as being for the  
benefit of or creating any obligation toward any  
third party of legal entity outside ATN and the  
Customer; ATN’s obligations under this Agree-  
ment extend solely to the Customer. ATN’s li-  
ability hereunder for damages, regardless  
of the form or action, shall not exceed the  
fees or other charges paid to ATN by the  
customer or customer’s dealer. ATN shall  
not, in any event, be liable for special, indi-  
rect, incidental or consequential damages,  
including, but not limited to, lost income,  
lost revenue or lost profit, whether such  
damages were foreseeable or not at the  
time of purchase, and whether or not such  
damages arise out of a breach of warranty,  
a breach of agreement, negligence, strict li-  
ability or any other theory of liability.  
PRODuCT WARRANTY REGISTRATION  
In order to validate the warranty on your prod-  
uct, ATN must receive a completed Product  
Warranty Registration Card for each unit.  
Please complete the form below and immedi-  
ately mail it to our Service Center: ATN Corp. ,  
20 S. Linden Ave. Suite 1B, South San Francis-  
co, CA 94080. Products qualifying for warranty  
repair will be either repaired or replaced within  
10 business days of receipt of merchandise un-  
less the customer is notified otherwise.  
ObTAINING WARRANTY SERVICE  
To obtain warranty service on your unit, take  
or send the product, postage paid, with a copy  
of your sales receipt to our service center, ATN  
Corporation at the address noted above. All  
merchandise must be fully insured with the  
correct postage; ATN will not be responsible  
for improper postage or, missing or damaged  
merchandise during shipment.  
The customer understands and agrees that ex-  
cept for the foregoing warranty, no other war-  
ranties written or oral, statutory, expressed or  
implied, including any implied warranty of mer-  
chantability or fitness for a particular purpose,  
shall apply to the product. All such implied war-  
ranties are hereby and expressly disclaimed.  
6
 
For customer service and technical support, please contact  
American Technologies Network Corp.  
North American Office  
20 S. Linden Ave. Suite 1B, South San Francisco, CA 94080  
phone: 800-910-2862, 650-875-0130; fax: 650-875-0129  
European Office  
phone: 44(0)870-0111286, fax: 44(0) 845-3349142  
The following countries can use our  
toll free number 00 800 9102-8620  
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland  
©2006 ATN Corporation  
 

ADC Clothes Dryer ML 75 User Manual
ADTRAN Network Card SLC 5 U BR1TE III User Manual
Agri Fab Lawn Aerator 45 0299 User Manual
Airlink101 Switch AGSW2400 User Manual
Airlink Network Router PinPoint EDGE GPRS User Manual
Air O Swiss Humidifier AOS 7147 User Manual
AKG Acoustics Microphone D 3700 User Manual
Altina GPS Receiver GBT708 User Manual
Audiovox Satellite Radio PRO 94FR User Manual
Beko Clothes Dryer DPU 8340 X User Manual