24v driveN, FTP-607 Series
2” HiGH SPeed THerMaL PriNTer
FTP-627MCL401/601
n Overview
The FTP-627 MCL Series are 24V driven high-speed printers
with a ultra low profile auto cutter and long life.
The FTP-627 MCL Series can be used for a variety of
applications, such as POS terminals, ticket vending machines,
label printers, banking terminals, and measurement and
medical equipment.
n HiGHLiGHTS
FTP-627MCL401/601
• Ultra low profile
Height 21.8 mm, width 81.2 mm, depth 42.2 mm
• High speed printing
It can print at 100/150 mm/s (800/1,200 dotlines/s)
maximum by using Fujitsu's unique head drive control.
• Auto Cutter
Long life and high reliable guilotine with dedicated motor.
• Easy paper setting
Our lever platen release mechanism allows a
wide paper route, so paper can be easily inserted.
Conventional auto loading is also available.
FTP-627DSL291R
• Multifunctional die-cast frame
Wide operating temperature range, long continuous
printing, high ESD absorbtion and discharge of static
electricity vibration and shock resistant.
• RoHS compliant
FTP-627DSL601R
ꢀ
FTP-627MCL401/601
n SPeCiFiCaTiONS
Item
Specification
Iterface
Conforms to RS232C/Centronics / USB
Power supply For print head MCL401
24 VDC average current, 0.4A (0.9 A peak)
(print ratio: 12.5%, print speed 100mm/sec.)
MCL601
24 VDC average current 0.5 A (0.9 A peak)
24 VDC ±5%, 1 A maximum
For motor
For cutter
For logic
MCL401
MCL601
MCL401
MCL601
24 VDC ±5%, 1.1 A maximum
24 VDC ±5%, 1 A maximum
24 VDC ±5%, 1.3 A maximum
3.3 to 5.25 VDC, 0.1 A maximum
81.2 x 42.2 x 21.8 mm (WxDxH)
70 x 60 x 12 mm (WxDxH)
Dimensions
Mechanism with cutter
Interface
board
DSL291
DSL6xx
95 x 70 x 21.6 mm (WxDxH)
Weight
Mechanism with cutter
Interface board
Approximately 100g
Approximately 50g
Life
Head
MCL401
Pulse durability: 50 million pulses/dot (print ratio: 25%).
Pulse durability: 100 million pulses/dot (print ratio: 25%).
Abrasion resistance: paper traveling distance 50km
Abrasion resistance: paper traveling distance 100km
500,000 cuts
MCL601
MCL401
MCL601
MCL401
MCL601
Cutter
Platen
1,000,000 cuts
5,000 times (open/close)
Operating
environment
Operating temperature*
Operating humidity
Storage temperature
Storage humidity
0ºC to +50ºC
20 to 85% RH (no condensation)
-20ºC to +60ºC (paper not included)
5 to 95% RH (no condensation)
Detected by thermistor
Detection
function
Head temperature
detection
Paper out/mark
detection
Detected by photo-interruptor
Platen release
Detected by sliding switch
Recommended thermal sensitive paper
High sensitive paper
Standard paper
TF50KS-E4 (Nippon paper)
TF60KS-E (Nippon paper),
FTP-020PU001 (58mm)
PD150R (Oji paper)
FTP-020PU701 (58mm)
Medium life storage
TF60KS-F1 (Nippon paper)
FTP-020P0102 (58mm)
PD170R (Oji paper)
paper
P220VBB-1 (Mitsubishi paper)
Long life storage
PD160R (Oji paper)
paper
AFP-235 (Mitsubishi paper)
TP50KJ-R (Nippon paper)
HA220AA (Nippon paper)
*+5˚C to +40˚C printing density assurance rance.
ꢁ
FTP-627MCL401/601
n FuNCTiON OF iNTerFaCe bOard
Item
Item
1.
2.
3.
4.
5.
Test print function
8.
Cutter trouble detect
Paper out detection
Paper near end detection
Paten open detection
9.
Motor power saving function
Mark detection function
10.
11.
12.
MCU operation abnormality detection
Power ON/OFF sequence protection
Thermal head temperature abnormality
detection
6.
7.
Blow-out fuse detection
13.
14.
Motor over-current protection
Hardware timer
Head voltage abnormality detection
n diMeNSiONS
1. Printer mechanism
FTP-627MCL401/601
68.4
25
21.8
7.5
44
60
81.2
ꢀꢀ°
44
10.7
Unit: mm
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).
2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is
open.
4
FTP-627MCL401/601
2. Interface board FTP-627DSL291R
(70.0)
63.5
3.25
3.25
50.5
25.5
1.45
ꢀ
24
8
ꢀ
CNꢁ
CN4
FG¯3.2
CN7
3ѯ3.2
CN6
CN2
8
ꢀ
ꢀ
ꢀ
6
ꢁ
17.5
1.25
34.5
49.5
Note: all dimensions are nominal value
() means just reference
The mounting height is the max.
Unit: mm
5
FTP-627MCL401/601
n iNTerFaCe bOard FTP-627dSL601 Series
Connectors on Control Board
Name
Functions
Remarks
Note
CNꢀ +24V power supply connector Connection for +24V power supply
CN2 RS-232C
Connection for serial interface
Connection for USB interface
CNꢁ USB I/F connector
CN4
-
Connection for thermal head + paper feed motor 2-inch, 30 pin
Connection for paper cutter
CN5 Cutter connector
CN6 Operation panel connector
CN7 Near end sensor connector
Connection for operation panel
Connection for near end switch
-
*ꢀ
*2
CN8
-
CN9 Logic power connector
CN10 Head/motor connector
Connection for +5V power Supply
Connection for thermal head & paper feed motor 2-inch, 24 pin
Note: *1: Option
*2: Depends on specification
6
FTP-627MCL401/601
FTP-627MCL401
1. Connector (FPC) specification (CN3/CN10)
(1) Connector
Mechanical unit side:
FPC connector
Remote side (housing site):
52610-2471 (made by Molex)
(2) Pin assignment on the mechanical side
Signal
PHK
I/ O Contents
No
1
—
I
Photointerrupter (Cathode)
2
VSEN
PHE
VH
Ground power supply for paper sensor
Photointerrupter (Emittor)
Head drive power
Data input
3
O
I
4
5
DI
I
6
STB2
STB3
VDD
GND
I
Print enable signal 2
Print enable signal 3
Logic Power
7
I
8
I
9
—
—
—
O
I
Head ground
10 GND
11 GND
12 TH
Head ground
Head ground
Thermistor
13 STB1
14 LAT
15 CLK
16 VH
Print enable signal 1
Data Latch
I
I
Clock
I
Head drive power
Head drive power
Platen open switch
Platen open switch
Motor excite signal A
Motor excite signal A
Motor excite signal B
Motor excite signal B
Not connected
17 VH
I
18 SW
19 SW
20 MT A
21 MT A
22 MT B
23 MT B
24 NC
—
—
I
I
I
I
—
7
FTP-627MCL401/601
FTP-627MCL601
1. Connector (FPC) specification (CN4)
(1) Connector
Mechanical unit side:
Remote side (housing site):
FPC connector
52610-3071 (made by Molex)
(2) Pin assignment on the mechanical side
No.
ꢀ
Symbol
PHK
VSEN
PHE
VH
Signal Name
Cathode for photo interrupter
Paper sensor power
Emitter for photo interrupter
Head drive power
Head drive power
Head drive power
Data in
2
ꢁ
4
5
VH
6
VH
7
DI
8
STB2
STB3
Vdd
Strobe 2
9
Strobe 3
10
ꢀꢀ
ꢀ2
ꢀꢁ
ꢀ4
15
ꢀ6
ꢀ7
18
19
20
2ꢀ
22
2ꢁ
24
25
26
27
28
29
30
Logic power
GND
GND
GND
GND
GND
GND
TM
Head ground
Head ground
Head ground
Head ground
Head ground
Head ground
Thermistor
NC
NC
STB1
LAT
Strobe 1
Data latch
CLK
VH
Clock
Head drive power
Head drive power
Head drive power
Platen switch
Platen switch
Excitation signal A
Excitation signal A
Excitation signal B
Excitation signal B
VH
VH
SW
SW
MT A
MT A
MT B
MT B
8
FTP-627MCL401/601
Sensor (Photo-
interruptor)
Platen unit
Thermal head
Motor
FPC
Connect terminal:
surface side
Connector No
24, 23, .....................2,1
(FPC pin numbers)
2. Cutter (CN4/CN5)
Connector on control circuit side: 52610-0871 Molex or equivalent
No. Signal I/O
Contents
No. Signal I/O
Contents
1
3
5
7
VSEN
PHK
I
O
I
Paper sensor power
Photo interruptor (cathode)
Motor excite signal A
Motor excite signal B
2
4
6
8
PHE
MT A
MT B
NC
O
I
Photo interruptor (emittor)
Motor excite signal A
Motor excite signal B
Not connected
MT A
MT B
I
I
—
Fujitsu Components International Headquarter Offices
Japan
Europe
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Web: emea.fujitsu.com/components/
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Fax: (1-408) 745-4970
Tel: (65) 6375-8560
Email: [email protected]
Fax: (65) 6273-3021
Email: [email protected]
©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective
owners.
Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our
products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice.
Rev. November 6, 2008.
9
|